|
ASTM-C1374
|
1997
|
Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Bu
|
|
ASTM-C1375
|
2000
|
Standard Guide for Substrates Used in Testing Building Seals and Sealants
|
|
ASTM-C1376
|
1997
|
Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Glass
|
|
ASTM-C1377
|
1997
|
Standard Test Method for Calibration of Surface/Stress Measuring Devices
|
|
ASTM-C1378
|
1997
|
Standard Test Method for Determination of Resistance to Staining
|
|
ASTM-C1379
|
1997
|
Standard Test Method for Analysis of Urine for Uranium-235 and Uranium-238 Isotopes by Inductively C
|
|
ASTM-C138
|
2001
|
Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete AAS
|
|
ASTM-C1380
|
1997
|
Standard Test Method for Determination of Uranium Content and Isotopic Composition by Isotope Diluti
|
|
ASTM-C1381
|
1997
|
Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts E(01-jun-2002) R(2002)
|
|
ASTM-C1382
|
2002
|
Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation
|
|
ASTM-C1383
|
1998
|
Standard Test Method for Measuring the P-Wave Speed and the Thickness of Concrete Plates Using the I
|
|
ASTM-C1384
|
2000
|
Standard Specification for Admixtures for Masonry Mortars
|
|
ASTM-C1385
|
1998
|
Standard Practice for Sampling Materials for Shotcrete
|
|
ASTM-C1386
|
1998
|
Standard Specification for Precast Autoclaved Aerated Concrete (PAAC) Wall Construction Units
|
|
ASTM-C1387
|
1998
|
Standard Guide for Determination of Technetium-99 in Soil
|
|
ASTM-C139
|
2001
|
Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
|
|
ASTM-C1392
|
2000
|
Standard Guide for Evaluating Failure of Structural Sealant Glazing
|
|
ASTM-C1393
|
2000
|
Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation
|
|
ASTM-C1394
|
1998
|
Standard Guide for In-Situ Structural Silicone Glazing Evaluation
|
|
ASTM-C1395
|
2001
|
Specification for Gypsum Ceiling Board
|
|
ASTM-C1396
|
2000
|
Standard Specification for Gypsum Board
|
|
ASTM-C1397
|
1998
|
Standard Practice for Application of Class PB Exterior Insulation and Finish Systems
|
|
ASTM-C1398
|
1998
|
Standard Test Method for Laboratory Determination of Time Setting of Hydraulic-Cement Mortars Contai
|
|
ASTM-C1399
|
2002
|
Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
|
|
ASTM-C14
|
1999
|
Standard Specification for Concrete Sewer, Storm Drain, and Culvert Pipe
|
|
ASTM-C140
|
2002
|
Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
|
|
ASTM-C1400
|
2001
|
Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls
|
|
ASTM-C1401
|
2002
|
Standard Guide for Structural Sealant Glazing
|
|
ASTM-C1402
|
1998
|
Standard Guide for High-Resolution Gamma-Ray Spectrometry of Soil Samples
|
|
ASTM-C1403
|
2000
|
Standard Test Method for Rate of Water Absorption of Masonry Mortars
|
|
ASTM-C1404
|
1998
|
Standard Test Method for Bond Strength of Adhesive Systems Used with Concrete as Measured by Direct
|
|
ASTM-C1405
|
2001
|
Standard Specification for Glazed Brick (Single Fired, Solid Brick Units)
|
|
ASTM-C1407
|
1998
|
Standard Practice for Calculating Areas, Volume, and Linear Change of Refractory Shapes
|
|
ASTM-C1408
|
1998
|
Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets by Direct Combustion-In
|
|
ASTM-C1409
|
1998
|
Standard Guide for Measuring and Estimating Quantities of Insulated Piping and Components
|
|
ASTM-C141
|
1997
|
Standard Specification for Hydraulic Hydrated Lime for Structural Purposes
|
|
ASTM-C1410
|
1998
|
Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation
|
|
ASTM-C1411
|
2001
|
Standard Practice for the Ion Exchange Separation of Uranium and Plutonium Prior to Isotopic Analysi
|
|
ASTM-C1413
|
1999
|
Standard Test Method for Isotopic Analysis of Hydrolyzed Uranium Hexafluoride and Uranyl Nitrate Sol
|
|
ASTM-C1414
|
2001
|
Standard Practice for the Separation of Americium from Plutonium by Ion Exchange
|
|
ASTM-C1415
|
2001
|
Standard Test Method for 238Pu Isotopic Abundance by Alpha Spectrometry
|
|
ASTM-C1416
|
1999
|
Standard Test Method for Uranium Analysis in Natural and Waste Water by X-Ray Fluorescence
|
|
ASTM-C1417
|
2002
|
Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe f
|
|
ASTM-C1419
|
1999
|
Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in O
|
|
ASTM-C142
|
1997
|
Standard Test Method for Clay Lumps and Friable Particles in Aggregates AASHTO No.: T112
|
|
ASTM-C1420
|
1999
|
Standard Guide for Selection, Removal, and Shipment of Manufactured Masonry Units Placed in Usage
|
|
ASTM-C1421
|
2001
|
Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temper
|
|
ASTM-C1422
|
1999
|
Standard Specification for Chemically Strengthened Flat Glass
|
|
ASTM-C1423
|
1998
|
Standard Guide for Selecting Jacketing Materials for Thermal Insulation
|
|
ASTM-C1424
|
1999
|
Standard Test Method for Monotonic Compressive Strength of Advanced Ceramics at Ambient Temperature
|
