11.43.54
|
INSULATING FLANGES, WELDING NECK,CARBON-;STEEL,FORGED CARBON STEEL TO ASTM A 105;GRADE 1 OR 2 FACING AND DRILLING TO ANSI B;16.5 BUT DRILLED BOLT HOLES 1/16 IN LARGER;THAN STANDARD BOLT HOLES TO RECEIVE 1/32 IN.;THICK INSULATING SLEEVE FLANGES TO BE DRILL
Area :
ANSI
JA :
NIGC
|
11.43.55
|
INSULATING JOINT, CLASS 600, BUTT WELD END,;MONO BLOCK, CONSTRUCTION TYPE, ACCORDING TO ANSI B31.8;GAS PRESSURE PIPING W/DESIGN FACTOR OF 0.5;MAX. PRESSURE 1050 PSI, CONFORMING TO IGS-M-PL-006(1);LOCATION:GAS DISTRIBUTION NO. 4 (ML);FOR ORDERING THE ABOVE
Area :
ANSI
Type :
IRAN.
JA :
NIGC
|
11.43.56
|
PARTS FOR: CORROSION PROBE ACCESS FITTING,;GRANT OIL TOOL (COSASCO);SUPPLIER REF. NO. HC-642/REV. B/M 30-305;SUPPLIER: GRANT OIL TOOL CO.,COSASCO DIV.;2042 EAST VERNON AVE LOS ANGELES,CALIF.90058;LOCATION:KHANGIRAN REFINERY KG;ORDER NO: 048
JA :
NIGC
|
11.43.58
|
COAL COKE;COAL COKE BREEZE TYPE 1 OF IRANIAN PETROLEUM;STANDARD NO: IPS-M-TP-750-PART 2 COMPRISING:;CARBON CONTENT: MIN 80%;MOISTURE CONTENT: MAX 5%;BULK DENSITY: 650-800 KG/CUBIC METER;ELECTRICAL RESISTIVITY:LESS THAN 100 OHM/CM;PARTICLE SIZE: 100% LESS
Type :
IRAN.
JA :
NIGC
|
11.43.59
|
BAGS, TIGHTLY WOVEN, ALIKE TO ACCEPTED PROOF;FOR FILLING COAL COKE BREEZE MESC.6530773054;NOTE EMPTY BAGS SHOULD BE RETURNED TO STORE
JA :
NIGC
|
11.43.60
|
CARBONACEOUS BACKFILL, FIRE COKE BREEZE,;HIGH TEMPERATURE, MINIMUM CARBON CONTENT 95%;MAX.RESISTIVITY 50 OHMS/CM WHEN DRY AND;LIGHTLY TAMPED AND PRIOR TO THE ADDITION OF;LIME, GRAIN SIZE SUCH THAT 100% WILL PASS;1/2 IN. MESH AND 85% TO PASS 1/8 IN.MESH;W/
Area :
EN
JA :
NIGC
|
11.43.61
|
SPLICING TAPE FOR INSULATING OF C.P. WIRES
JA :
NIGC
|
11.43.62
|
FLANGE INSULATION KIT FOR CATHODIC-;PROTECTION SUITABLE FOR ANSI RAISED FACE;FLANGES KIT CONSISTING OF ONE NEOPRENE-FACED;MICARTA(PHENOLIC)CENTRAL GASKET(TYPE E)1/8;IN. THICK DRILLED TO RECEIVE BOLTS&SLEEVES,;ONE POLYETHYLENE SLEEVE OF 1/32 IN. THICK;PER
Area :
ANSI
Type :
IRAN.
JA :
NIGC
|
11.43.63
|
INSULATING FLAT CENTRAL GASKET ONLY 1/8 IN.;THICK FOR FLANGE INSULATION, MADE FROM A;FLAT SHEET OF MEDIUM WEAVE FABRIC BASE;LAMINATED THERMOSETTING PHENOLIC WITH;NEOPRENE COATING ON BOTH FACE;F.H. MALONEY
Type :
IRAN.
JA :
NIGC
|
11.43.64
|
FLANGE INSULATION KIT F/CATHODIC PROTECTION;SULTABLE FOR USE WITH ANSI R.F. FLANGES TYPE;F GASKET MATERIAL OF NEOPRENE FACED PHENOLIC;& 1/8 IN. THICK C/W ONE FULL LENGHT;INSULATED SLEEVE OF 1/32 IN. THICK & MIN.;DIEKECTRIC STRENGTH 160000 V/MM PER BOLT,;T
Area :
ANSI
Type :
IRAN.
JA :
NIGC
|
11.43.65
|
FLANGE INSULATION KIT F/CATHODIC PROTECTION;5 HOLE FIBER INSULATION SLEEVE 25 MM;WITH TWO SLEEVES & METALL WASHERS & STULD BOLLS;LOCATION: SARKHON PROGECT
JA :
NIGC
|
11.43.66
|
PIPELINE CROSSING INSULATORS, STEEL BAND;TYPE 8 IN. WIDE, RIBBED RUBBER LINING 1/8 IN;THICK POLYESTER/FIBREGLASS RUNNERS OF 1-1/2;IN.HEIGHT;MALONEY TYPE 63 PF OR EQUIVALENT;NOTE: HEAVY DUTY CONSTRUCTION INSULATOR FOR;HEAVY, LARGE SIZE AND LONG CASED SECT
JA :
NIGC
|
11.43.67
|
INSULATING RING ENCIRCLING TYPE (CENTRING-;CRADLE) PLASTIC TO BE USED AT EACH END OF;CARRIER PIPE;REF T.D.WILLIAMSON, F.H.MALONEY, MAPEL OR;ANY OTHER SUPPLIER
JA :
NIGC
|
11.43.68
|
BLOCK & CABLE INSULATOR RING (M-2 PLASTIC-;THINSULATOR) TO BE USED PLACED ON THE;CARRIER PIPE BEFORE PLACING INSIDE THE;CASING PIPE;REF T.D.WILLIAMSON, F.H.MALONEY, MAPEL OR;ANY OTHER SUPPLIER
JA :
NIGC
|
11.43.69
|
PIPELINE CROSSING INSULATOR MOULDED TYPE;HIGH DENSITY POLYETHYLENE RUBBERS MOULDED;INTEGRAL WITH INSULATOR RIBBED INNER;SURFACE ACC. TO IGS-MS-TP-012(2):1998 STD
Type :
IRAN.
JA :
NIGC
|
11.43.70
|
CASING END SEAL, RUBBER MOULDED TYPE,SLIP-ON;ALLOWING MAXIMUM LATERAL AND LONGITUOINAL;SHIFTING OF CARRIER PIPE, MINIMUM THICKNESS;3/16 IN. IN BELLOWS TO 1/2 IN.THICK AT;SHOULDER COMPLETE WITH THUMBSCREW CLIPS AND;S.S.BANDS;F.H.MALONEY MULTIFLEX MOULDED T
Type :
IRAN.
JA :
NIGC
|
11.43.71
|
CASING END SEAL, Z TYPE RUBBER MOULDED TYPE;SLIP-ON ALLOWING MAX. LATERAL & LONGITUOINAL;SHIFTING OF CARRIER PIPE, MIN. THICKNESS;3/16 IN. IN BELLOWS TO 1/2 IN. THICK. AT;SHOULDER COMPLETE WITH THUMBSCREW CLIPS AND;S.S. BANDS;REF. T.D. WILLIANSON INC. OR
Type :
IRAN.
JA :
NIGC
|
11.43.72
|
CASING END SEALS, PULL ON TYPE, ONE PIECE;SHAPE SYNTHETIC RUBBER 1/8 IN. THICK, BANDED;TO THE CARRIER PIPE AND CASING BY 1/2 IN.;ST.ST. BAND COMPLETE WITH ST.ST. BAND;F.H.MALONEY TYPE OR EQUIVALENT
Type :
IRAN.
JA :
NIGC
|
11.43.73
|
CASING SEALS, ZIPPER TYPE,SEAL MAT.SYNTHETIC;RUBBER 1/8 IN.THICK,OIL & WATER RESISTANCE;ZIPPER MAT.ST.ST.& TO BE PRESSURE MOULDED TO;THE RUBBER SEAL.RUBBER PROTECTIVE STRIP MUST;BE ATTACHED TO THE SEAL UNDER THE ZIPPER.;TO BE SUPPLIED WITH TWO 1/2 IN.ST.S
Type :
IRAN.
JA :
NIGC
|
11.43.74
|
NEWTON-DERBY PERMANENT PILOT EXCITER;TYPE F7230, FRAME SIZE M824, SER NO.30153611;1.75 KVA, 1.61 KW,225VOLT,CLASS B INSULATION;7.7 AMP. DC, 1500 RPM;SUPPLIER: NEWTON BROTHER-DERBY;LOCATION:BIDBOLAND REFINERY BB;USED FOR 9375 KVA, 7500 KW, 11
JA :
NIGC
|
