|
ISO-11486
|
2003
|
Two-wheeled motorcycles-Fuel consumption measurements – Chassis
dynamometer setting by coastdown met
|
|
ISO-11489
|
2005
|
Determination Of Platinum in Platinum Jeweler alloysR08;Gravimetricdetermination by reduction with m
|
|
ISO-11490
|
2005
|
Determination of Palladium in Palladium Jeweleralloys –Gravimetricdetermination withdimethylglyoxime
|
|
ISO-11496
|
1999
|
WELDED STEEL TUBES FOR PRESSURE PURPOSES _ ULTRASONIC TESTING
|
|
ISO-11501
|
2000
|
Plastics - Film and Sheeting - Determination of Dimensional Change on Heating First Editio
|
|
ISO-11502
|
2005
|
Methods of testing Plastics — Part 8: Other properties — Method 825A: Film and sheeting — Determinat
|
|
ISO-11502-200
|
2005
|
Plastics – Film and sheet – Determination of blocking resistance – Test
methods
|
|
ISO-11503
|
2004
|
Paints and varnishes -- Determination of resistance to humidity - Part 2:
Intermittent condensation
|
|
ISO-11507
|
2007
|
Paints and varnishes Exposure of coatings to artificial weathering – Exposure
to fluorescent UV lamp
|
|
ISO-1151-1
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; Part 1:Aircraft motion rel
|
|
ISO-11512
|
2009
|
Machinery for forestry - Tracked special machines - Performance criteria for
brake systems
|
|
ISO-1151-2
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; Part 2 :Motions of aircraf
|
|
ISO-1151-3
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; Part 3 :Derivatives of for
|
|
ISO-1151-4
|
2004
|
Aerospace Flight dynamics R08; Concepts, quantities and symbols part4:Concepts , quantities and sym
|
|
ISO-1151-5
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; Part 5:Quantities used in
|
|
ISO-1151-6
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; part 6:Aircraft geometry
|
|
ISO-1151-7
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; part 7:Flight points and f
|
|
ISO-1151-8
|
2004
|
Aerospace R08; Flight dynamics – Concepts, quantities and symbols – Part 8 :Concepts and quantities
|
|
ISO-1151-9
|
2004
|
Aerospace R08; Flight dynamics R08; Concepts, quantities and symbols R08; Part 9:Models of atmospher
|
|
ISO-11519-1
|
2007
|
Road vehicles – Low speed serial data communication –R08; Part 1: Terminologyand definitions
|
|
ISO-11520-1
|
2003
|
Agricultural machinery R08; Grain driers R08; Determination of performance R08; Part1: General
|
|
ISO-11541
|
2002
|
Natural gas-Determination of water content at high pressure
|
|
ISO-11543
|
2008
|
Modified starch Determination of hydroxypropyl content Method using
proton nuclear magnetic resonanc
|
|
ISO-11545
|
2003
|
Agricultural irrigation equipment – Centre pivot and moving lateral irrigation
machines with sprayer
|
|
ISO-11553-1
|
2009
|
Safety of machinery — Laser processing machines — Part 1:General safetyrequirements
|
|
ISO-11554
|
1999
|
Optics and Optical Instruments - Lasers and Laser-Related Equipment - Test Methods for Laser Beam Po
|
|
ISO-11556
|
2007
|
Paper and board – Determination of curl using a single vertically suspended
test piece Test method
|
|
ISO-11562
|
2000
|
Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Metrological Characteri
|
|
ISO-11565-12
|
2007
|
Road vehicles Spark plugs Test methods and requirements
|
|
ISO-11566
|
2004
|
Carbon fibres - Determination of tensile properties of single- Filament
specimens test method
|
|
ISO-11567
|
2004
|
Carbon fibres - Determination of filament diameter and cross-sectional area
|
|
ISO-11568-2
|
2008
|
Banking – Key management (retail) R08; Part 2: Symmetric ciphers Their keymanagement and life cycle
|
|
ISO-1158
|
1996
|
PLASTICS - DETERMINATION OF VINYL ACETATE IN VINYL CHLORIDE VINYL
ACETATE COPOLYMERS
|
|
ISO-1159
|
1996
|
PLASTICS - DETERMINATION OF THE RESISTANCE OF PLASTICS TO CHEMICAL
SUBSTONCES
|
|
ISO-11591
|
2001
|
Small Craft, Engine Driven - Field of Vision from Helm Position (Q)
|
|
ISO-11592
|
2003
|
Marine industries- Small craft less than 8 m length of hull- Determination of
maximum propulsion pow
|
|
ISO-11593
|
1998
|
Manipulating Industrial Robots - Automatic End Effector Systems - Vocabulary and Presentation of Cha
|
|
ISO-11600
|
2007
|
Jointing products Classification and requirements for sealants - Specifications
|
|
ISO-11602-1
|
2010
|
Fire protection Portable and wheeled fire extinguishersR08; Part 1: Selectionand installation
|
|
ISO-11602-2
|
2010
|
Fire protection Portable and wheeled fire extinguishersR08; Part 2: Inspectionand maintenance
|
|
ISO-11606
|
2005
|
Ships and marine technology – Marine electromagnetic compasses
|
|
ISO-11607-1
|
2000
|
Packaging for terminally sterilized medical devices-Part 1: Requirements for materials,sterile barri
|
|
ISO-11607-2
|
2000
|
Packaging for terminally sterilized medical devices-Part 2: Validation requirements for forming, sea
|
|
ISO-11614
|
2007
|
Reciprocating internal combustion compression ignition engines - Apparatus
for measurement of the op
|
|
ISO-11623
|
2002
|
Transportable Gas Cylinders - Periodic Inspection and Testing of Composite Gas Cylinders (H)
|
|
ISO-11625
|
2004
|
Gas cylinders – Safe handling
|
|
ISO-11632
|
2009
|
Determination of mass concentration of sulfur dioxide- Stationary source
emissions- Ion chromatograp
|
|
ISO-11640
|
2002
|
Leather -- colour fastness -- to-and-fro rubbing -- Test method
|
|
ISO-11641
|
2001
|
Leather - Colour fastness to perspiration -Test method
|
|
ISO-11642
|
2002
|
Leather - colour fastness - colourfastness To water - test method
|
